Introduction
Deciding between SMD (Solder Mask Defined) and NSMD (Non-Solder Mask Defined) pads might be vital when designing PCBs. These two pad types intrude on soldering precision, reliability, and PCB layout design considerations. Here in this guide, we will look at what SMD vs NSMD are, what each offers and how it affects your options when it comes to your PCBs.
What is SMD?
Solder Mask Defined is a special pad design on your PCB. It uses solder mask to cover most of the copper pad. Only a small section is left exposed for soldering. This exposed area depends on the solder mask opening. SMD pads are useful for precise soldering. They help guide the solder, especially for small components like BGA balls. This design also improves reliability and device performance. Limiting the exposed copper ensures accurate connections.

What is NSMD?
Non Solder Mask Defined is a form of pad on a PCB or a printed circuit board. Contrary to other designs, the solder mask does not cover the copper pad. It separates a border around it and as a result exposes the whole of the pad. This full exposure ensures that the solder stick well on the pad. NSMD pads also enable use of relatively small pad sizes. This makes it easier to route traces for pretty compact designs, such as BGAs. It is very useful for high density and where accurate layout is required.

SMD and NSMD Characteristics Comparison
This table highlights the differences between the SMD and NSMD pad designs when it comes to size, soldering precision, alignment, cost and application where the designs can be used.
Characteristics | SMD | NSMD |
| Mask Opening Vs. Pad | Same size as the pad. | Larger than the pad by at least 150 μm. |
| Solder Volume Control | Controlled by the mask opening. | Controlled by the size of the pad. |
| Pad Shape | Mask overlaps the edges of the pad. | Entire pad is fully exposed, no overlap. |
| Pad Coverage | Limited to the mask opening area. | Full pad area is exposed for soldering. |
| Bridging Risk | Lower because mask dams stop solder from spreading. | Higher because no dams require careful spacing. |
| Registration Needs | Precise alignment of mask to pad is critical. | Less strict alignment is needed for pads. |
| Solder Voiding | Higher risk due to smaller solder volumes. | Lower risk thanks to more solder paste. |
| Design Cost | Higher due to tighter tolerances. | Lower because tolerances are more flexible. |
| Solder Joint Strength | Creates more precise joints and reduces bridging. | Stronger bonds due to better solder flow. |
| Application | Ideal for small components needing accuracy. | Better for strong mechanical connections. |
SMD vs NSMD Pad Type for BGA Package
In BGA packages, SMD and NSMD are involved. SMD pads basically align the solder mask opening to the size of pads. This design assist in soldering operations and also small or fine-pitch form components. But it can have an adverse effect of contributing to the formation of solder voids. Compared to pad size, NSMD pads have openings on the solder mask which are larger. This minimizes void risks and also makes it possible to accommodate tolerances while soldering. NSMD pads also require a greater amount of space even around them. The options are only limited by the size of your BGA pitch, the number of pads you want, and the overall size. You also need to factor your manufacturing process capabilities when making this decision.

Advantages and Disadvantages of SMD and NSMD
SMD (Solder Mask Defined)
Advantages
- Suitable For Small Component Pads – Great for tiny components like 0402, 0201, and 01005. These pads’ shapes stay consistent.
- Less Prone to Tearing and Detachment – Sturdier during rework. They have a bigger copper foil area and are partially covered by soldermask.
- Has Stronger Bond – It gives a stronger connection between the pad and the FR4 substrate because it has larger copper foil and soldermask coverage.
Disadvantages
- Increased Stencil Thickness and Solder Volume – SMD pads have a thicker stencil because of the soldermask. Adds more solder paste. It sometimes increase the risk of short circuits during manufacturing.
- Reduced Copper Surface Area and Layout Challenges – SMD pads leave less copper for soldering and reduce the space between pads that’s why it is harder to design traces and use through-holes in this pad type.
- Weaker Solder Strength – Tends to have a weaker solder bond. This is because of their smaller size and the effect of thermal expansion and contraction during soldering.

NSMD (Non-Solder Mask Defined)
Advantages
- Larger Solderable Area and Improved Joint Strength – It offers more surface area for that is great for soldering that is needed in having stronger reliable joints.
- Greater Spacing and Enhanced Layout Flexibility – It gives you more room for traces and better flexibility in your PCB design because of the wider spacing between pads.
Disadvantages
- Prone to Tombstone Effect – Can cause the “tombstone” effect. Tombstone components lift during soldering if the pads are not sized right and it will affect the quality of the PCB.
- Increased Risk of Detachment During Repair – These pads are isolated that they can be more prone to coming loose during rework or repairs.
- Accumulation of Flux Residue and Solder Balls – The areas not covered by soldermask because of NSMD method can collect flux residue and solder balls and that will affect the PCB as a whole.

Guidelines in Using SMD vs NSMD in PCB Manufacturing
For SMD:
- Pad Diameter Alignment: The pad diameter must be 20 to 60 μm smaller than the mask opening. Adjust for registration accuracy so the pads are adequately covered during soldering.
- Mask Opening Spacing: The spacing between two mask openings should be at least 50 to 75 μm. More space between the openings minimizes solder bridging.
- LCMD Vias for Tight Spaces: LCMD vias can be used within the pad area in cases where space is very limited. It will help fit more components into the board.
- Pad-to-Ball Ratio: For perimeter balls, the pad-to-ball ratio must be 1:1. Needed so each ball has adequate area on it to make a good solder joint.
- Area Array for Non-Perimeter Pads: You have to use area arrays for non-perimeter pads. That helps to increase routing flexibility while creating more free space for the implementation of other components especially within very complex designs.
- Non-Critical Pad Shapes: The shape of the SMD pad is not very critical because solder mask controls both the shape and volume of solder. This gives more freedom in design without affecting performance.
- No Thermal Reliefs in Pads: Try to avoid using thermal relief in the pads since it will affect small volumes of paste. Thermal relief degrades the soldering ability, particularly with smaller packages.
- Tighter Tolerances for Dense Footprints: For dense footprints, it should be used with tighter mask-to-pad tolerances to minimize web size and make better soldering. Connectivity will be improved even in compact designs.
- Offset Rows for Spacing: You have to space the adjacent rows or columns at 50% of pitch. It allows traceable routes to fit into a high-density layout and maximize use of space.
- Thicker Masks for Protection: A solder mask of at least 150 μm may be used for protecting solder during the reflow cycle. A larger mask prevents a solder from getting too ropy and proves useful in avoiding damage that is caused to pads.

For NSMD:
- Pad and Mask Opening Relationship: Diameter of the pad should be at least 150 μm smaller than the mask opening. This is needed so solder mask does not interfere with the soldering area of the pad for a clean solder joint.
- Mask Opening Spacing: You need to maintain at least 225 μm between the mask openings. Needed to avoid solder bridging during reflow between pads.
- Specialized Pad Shapes: In order to enhance solder filling, use dogbone or dumbbell-shaped pads. Creates a better solder joint for more demanding components.
- LCMD Vias Placement: LCMD vias should be placed at a distance from the extended edges of the pad. If not done correctly, it may affect the integrity of the solder joint. It will further create problems during the assembly process.
- Pad Assignment for Perimeter Balls: For perimeter balls, 1:1 pad to ball ratio is recommended. Guarantees strong and reliable solder joints for the balls on the outer edges of the BGA.
- Incorporation of Thermal Reliefs: In NSMD, thermal reliefs can be introduced into pad designs to enhance the thermal management of soldering. For better overall reliability of the joint in high-power applications.
- Increased Pad Spacing: As there is no solder dam between pads, the spacing of pads will have to be increased for avoiding solder bridging. Helps in improving the separation and decrease the chances of short circuits.
- Thinner Solder Mask Usage: Where the bridging risk is very low, thin solder masks which thickness can be as low as 75m are helpful in thinner overall thickness and this may make positioning of pads easier not to mention solving the soldering process.
- Relaxed Mask-to-Pad Registration: NSMD designs can relax mask-to-pad registration that may facilitate faster assembly. Beneficial in high-speed manufacturing where speed is needed.
- Limited Row/Column Shifting: You may shift the adjacent rows or columns up to 25% of the pitch. Keep it under 25% because too much shifting might increase the solder bridging risk.
- Recommended for Larger Footprints: Best suited for larger footprints, typically those above 15mm × 15mm. Works well for larger, more complex components that require additional space.

Applications of SMD and NSMD
SMD
SMD is widely used in high-density designs where space is limited and precision is required like the following:
- Fine pitch BGAs ≤ 0.8mm
- Small BGAs ≤ 0.5mm
- High pin count packages
- Portable electronics
NSMD
NSMD is more suited for larger, less dense designs where spacing between pads is less critical like these examples:
- Lower density BGAs >1mm pitch
- Larger packages >15mm x 15mm
- Automotive parts with stricter tolerances
- Corner ball cases with dogbone pads
- Boards with fewer routing layers
- Minimizing solder voiding
More FAQs about SMD vs NSMD
What Type of Pad Is Best for DM3730CBPD100: SMD Or NSMD?
Solder Mask Defined pads are preferred on the DM3730CBPD100, IC 515 pads 0.4mm pitch SMDs BGA. This recommendation has been inferred from working with OMAP35x EVM and BeagleBoard where NSMD pads at this pitch seem to have been most susceptible to solder bridging. However, where possible adequate control can be exercised in order to make proper use of NSMD pads, the use of SMD pads is employed here because they eliminate solder bridging factor and offer better quality in array PCB assembly.
Which Method is Preferred for BGA Pad Design: SMD Or NSMD?
As for the design of BGA pad, NSMD (Non-Solder Mask Defined) pad is popular than SMD (Solder Mask Defined) pad. By employing NSMD method, the BGA ball will collapse around the pad edge during the reflow process that improves the solder joint reliability level. In the case of SMD pads the ball does not lay down flat on the substrate which poses a problem for the joint.
What Is the Preferred Method for Other Components Like Chips, Sops, And Connectors?
As it has been established that the NSMD method is the best suited for BGA components. Other components including chips, SOPs and connectors depends. SMD pads are used for these components because the design and solder joint requirement of these components are different with that of BGA components. But, NSMD is useful in some elements for instance QFNs because the solder joint strength is of importance.
Why Do Some Manufacturers Recommend SMD Pad Design For Small Components Like LGA And uBGA Packages?
Some manufacturers believed that the SMD pads are lower in inductance as compared to through-hole pads in high frequency designs; thereby reducing the likelihood of occurrence of difficulties such as cross-talk or impedance mismatch. The given reasons are that lesser inductance can be in some applications for high speed signalling where signal integrity is important. Any solder mask that is surrounding SMD pads may help in the positioning of the element in an even better way especially for small parts. It can thus enhance the quality and reliability of the solder joints as discussed in this article.
Conclusion
If you have read this blog, you would understand the SMD vs NSMD pad designs and their impacts on your PCB. For PCBMay, we focus on making PCBs to exact specifications of density or volume, no matter how tiny the components, or more expansive and less packed in than other circuits. Please contact our team to discuss which type of pad design would be better for your project: SMD vs NSMD to achieve the greatest soldering quality and connection durability.
