Introduction
Solder beading is another of the typical imperfections of PCB production, which can negatively affect the qualities and stability of electronic circuits. This blog post focused on solder beading in details, discussing its types, causes and effects on PCB. Knowledge of this phenomenon is necessary for future preventive actions and for adherence to the norms of the industry.
What Is Solder Beading?
Solder beading is a situation where small round solder balls appear on your PCB. These beads are the effects of applying excessive solder paste at the time of assembling. They may pop up under components or vice versa, they may be found all over the board. Some solder beads can make electrical shorts from terminals to other terminals. This can cause severe circuit anomalies that in turn will lead to much worse situations. Solder beading is one of the most known defects in surface mount technology (SMT).

Types of Solder Beading
Solder beading can appear in different forms on your PCB. Let’s study these types so we can help you spot and fix solder issues.
· Mid-Chip Beading
It happens for example underneath the chip resistor, capacitors or inductors. It develops when excess solder paste pushes under a component during reflow soldering. The problem is this, and it usually comes down to poor paste application or low quality solder paste. Although it doesn’t always affect reliability it can cause electrical shorts which is a problem that needs to be avoided.

· Peripheral Beading
Normally this happens at the edges of components, for example at the borders of solder pads. It is caused from reflow when the solder paste spreads over to beyond the pad it is intended for. While, these beads are non destructive and don’t cause damage, they can cause cosmetic defects as well as can interfere in tightly packed designs.

· Random Beading
This is the solder balls, spread over the board. A common cause for this defect is solder paste spatter created during the reflow process; paste outgass from the reel or an uneven heat input are typical causes. Random beads are the worst, they can cause shorts anywhere on the board.

· Aligned Beading
It appears in a regular pattern across board features, such as component leads or edges. Most often, this defect results due to an error in consistent solder application or misaligned stencils. However, fewer in number, it can disrupt circuits in critical areas.

Solder Beading Occurrence in Different Soldering Technology
Solder beading can happen through any soldering technology with its own set of causes. We will help you pinpoint and solve the problem faster.
Solder Beading in Wave Soldering
- Wave Height is Excessive – In case the wave of solder is too high or tall then the solder here splashes over or overflows. This means that the board or near components leave solder beads behind. Maintaining the wave at the right size enables this not to happen.
- Bad Pallet Design – Solder can flow in unwanted directions if your pallet is bad. This may create formation of solder bead on edges. Proper adjustment of design will ensure proper flow during the soldering process.
- Contaminants In the Solder Pot – Dirty solder pots have introduced impurities in the solder. These impurities make a splatter and beads in the PCB. Cleaning from time to time reduces the chance of contamination.

Solder Beading in Reflow Soldering
- Characteristics of the Solder Paste – Wrong viscosity or spread in the paste results in excess material. It collects under components and, on heating, forms beads. The right paste and design of the stencil prevent this.
- Issues With the Reflow Profile – If the reflow temperature or time is incorrect, solder does not flow properly. This improper flow creates a bead. Proper profiling ensures even soldering.
- Components’ Outgassing- In reflow, there is pressure due to the evolution of moisture in the component and causes the solder to be pushed out in the form of beads. To get around this, pre-drying components is a good solution.

Solder Beading in Selective Soldering
- Faulty Nozzle Design – Bad designed or dirty nozzle prevents proper flow of solder. Will create solder beads around joints. It should be maintained for smooth functioning.
- Irregular Solder Flow – Solder flow rate changes causes irregular flow and uneven application. That causes a bead formation around the board. Monitoring and stabilizing the flow prevent this condition.
- Board Warping During the Soldering Process – Boards that warp because of heat provide spaces for solder to pool. Pooling promotes solder beads. Use rigid boards to reduces warping.

Factors that Causes for Solder Beading Formation
Solder beading is created when small balls of solder become formed in an undesirable area. Here are some things to look out for:
- Stencil and Pad Design – If the stencil openings do not match the pad pattern, solder will spread erratically and bead.
- Stencil Cleanliness – The dirty stencil may create excessive or misdirected solder paste with increased chance for beading.
- Machine Repeatability – During the soldering process, inconsistent movements of the machine may misalign solder placement and lead to beads.
- Reflow Temperature Profile – Solder splatter and even beads can occur if the heat is let run too hot or too fast.
- Chip Pressure – Excessive pressure during placement of chips onto the board pushes the solder out, and therefore beads are formed.
- Excess Solder Paste – If there is excessive solder paste, it will flow out of the pads, and it usually creates a bead during reflow.
- Tin Drop Height – Solder is dropping from too great a distance when placed, so it splats and beads on the board.
- Solder Mask Outgassing – Volatile substances released during heating can push solder paste out of place that will create beads.
- Flux Usage – Issues of too much or poor-quality flux can cause solder to splatter and form a bead.
Solder Beading Prevention
Solder beading is a common issue that can cause problems with the functionality of your PCB assembly but there are solutions to it. This is how the problem can be solved effectively.
Increasing Stencil Thickness
It is possible by using a thicker stencil for controlling the amount of solder paste applied. The right thickness means you are reducing excess paste which reduces the risk of solder beads. It’s a balancing act of getting the right amount of paste applied to the correct component and pad requirements.
Modifying Aperture Shape / Size
Solder paste deposition is directly dependent on the shape and size of stencil apertures. Adjust these to accommodate the component design. This is to prevent paste from flowing past the pads. This large improvement in solder quality can be accomplished in this small change.
Changing Viscosity of the Solder Paste
Solder paste of higher viscosity tends to minimize spreading of the paste during reflow process more than a paste with low viscosity. Better control means less solder bead risk and selecting the correct paste type enhances paste control for the application. Paste membership must always be matched to process requirements.
Adjusting the Reflow Profile
This has been backed up with evidence that a well optimized reflow profile can go a long way in preventing solder beading. By closely monitoring the heating and cooling processes, the paste’s behavior remains more or less reliable. This minimizes problems such as the paste slumping or the paste outgassing.
Modifying the Squeegee Speed and Pressure
To increase precision, one has to use moderation in squeegee velocity and force during paste application. Correct settings also award uniform paste deposition and reduce the presence of paste around the pads. These are improving settings that actually are apparent once change occur.
PCB Design Considerations
There is a way of ensuring that solder beading is never a problem in the first place and that is good PCB design. Pad spacing and alignment have to be done properly to make sure that paste bridging is also done properly. Talking to your PCB designer is important at this stage as well.
Environmental Control
Relative humidity and temperature that exist in the workplace determine the performance of solder pastes. It is well understood that constant environmental conditions are convenient to provide results free from problems like flux outgassing. The controlled environment leads to improved quality of soldering practices in general.
Effects of Solder Beading to PCB
It may seem reasonable and cause no issues, but solder beading is actually capable of causing extensive harm to the appearance, functionality, and reliability of your PCBs. Such effects can be varying from performance decrease to serious problems with the product durability.
Electrical Issues
Solder beads are a terrible thing on your board and can cause serious electrical trouble. The biggest risk with beads is that beads are liable to short circuit, perpetrators that interconnect conductors in a way that the circuit was not programmed for. It can also lead to suppression of signals by blocking the proper transmission of the signal to high frequency traces hence resulting to distortion and unreliable performance. Moreover, beads can add capacitance between the traces and change the response of the entire board. These electrical noises can cause a device to fail or completely stop working, which is why they need to be dealt with.
Mechanical Issues
For the mechanical point of view, solder beads can prevent the physical continuity of the PCB. These beads might help in protruding some compacts thereby wronging their positioning during assembly as well as the way they operate when in use. They can also decrease the amount of space between parts, which we come across when final assembling the individual parts into its final use. Eventually, beads give rise to stress points which may cause damages to the PCB or parts of it, leading to the decrease of the product’s durability and reliability.
Reliability Concerns
At times, solder beading may cause certain long-term reliability problems that are not easily noticed. Possibly some beads may have effect of reducing insulation resistance across the conductors which can cause electrical breakdown after sometimes. These can also move under specific circumstances and generate new flaws once the product is already being built. also, solder beads can melt in and capture chemicals, with the result that the board becomes more susceptible to adverse influences such as moisture or corrosion. These reliability issues explain why it is necessary to approach the solder beading problem from a preventative perspective.
Cosmetic Issues
Even though not influencing the usability at all times, the method results in solder beads that can reduce the aesthetic appeal of the PCB. Inconspicuous beads can be a problem for customers because they can notice grains that show the low quality of work and that they can doubt the quality of the product. In sectors that require products with uniform appearances, excess solder beads are likely to cause the product to be turned down.

Solder Beading Detection and Inspection Methods
Visual Inspection
Solder beading can easily be seen through a simple visual inspection. Magnifying glass or portable microscopes can be used by you or an inspector to look for visible defects to the naked eye. This method is fast without contact with the board, it is used for catching the surface problem such as solder beads, misalignment or bridging. It is basic and therefore may not discover ailment underneath a part.
X-ray Inspection
While the x-ray inspection is different from external assessment, as it examines the internal PCB structures. It operates under high energy and provides information on some unseen types of defects such as voids, solder bridges, and solder balls in different positions. This technique is used for visual inspection of Ball Grid Arrays (BGAs) and other parts of a substrate for which an optical telescope cannot be used. X-ray examination, however, is non-intrusive and very precise, although it usually needs sophisticated gear.
Electrical Testing
Functional testing involves input of stimuli into the circuit and then evaluating the behavior of the PCB. By using this one it is possible to check for open circuits or shorts or temporarily connected by solder beading. This method is based on PCB functionality, making the inspection a second check that complements visual and X-ray.

Standards for Acceptable Solder Beading Defects
IPC-A-610
This standard deals with the final inspection of Printed Circuit Board (PCB) assemblies and defines the parameters measured against which the soldered connections may be evaluated. It encompasses refined drawings of the recommended appearances and all the defect classifications so that producers can tell when they include solder beading amongst other problems..
J-STD-001
This deals with the procedures and chemicals applied during acquisition and soldering of the electronic parts. It includes a guide to the environmental control of the process and the different materials in soldering. While it provides information that works alongside IPC-A-610, regarding the base for assembly of the components but final product acceptance is not discussed.
IPC-7095
This is developed for the soldered components’ inspection and prescribes the inspection of soldering joints. It entails techniques for assessing defects like solder beading through tools that are complex such as X-ray..

FAQs on Solder Beading
What’s The Difference Between Solder Balling And Solder Beading?
Solder balling and solder beading are two different defects, which are common in the manufacturing of PCB. Solder balls usually occur in wave soldering or in hand soldering, it is observed that the solder balls appear randomly on the PCB. This can stem from wrong choice of solder or flux, too much solder or wrong soldering temperatures and in wave soldering, the machine may actually propel solder droplets onto the board. Solder beading, on the other hand, happens during the reflow soldering process, or when using large SMDs such as heavy chip capacitors. It is mainly attributed to over deposition of solder paste in the stencil printing process creating beads near the component leads when the paste is re-flowed in the oven.
Why Is My Solder Beading Instead of Sticking To The Iron Or Components?
Solder beading as opposed to wetting on the soldering iron or on the components is usually the result of such criteria such as poor quality of solder, lack or absence of flux, or incorrect temperatures of soldering. Perhaps the solder may be have been contaminated or may be of poor quality. If there are foreign particles on the solder, on the tip of the soldering iron, or on the components, adequate wetting and therefore the solder cannot ‘flow’ and adhere.
Why Am I Experiencing Solder Beading During Hot Plate Reflow Soldering?
Solder beading during hot plate reflow soldering is most often founded on two primary issues: over application of solder paste or improper temperatures profiles. The disadvantages of using a syringe are that it is difficult to apply a correct dose and it is difficult to avoid over-application when using paste, so a stencil is used. If a stencil is not possible then using a fine syringe tip and using a stand will increase steadiness. The reflow temperature curve must emulate that of the paste; for Sn42Bi57Ag1, staking time or temperature beyond the paste’s 138°C melting point will further result in beading.
Conclusion
For the PCB manufacturing, we at PCBMay know how crucial it is to have a perfect run through on the manufacturing process. Solder beading is a factor you will not want to ignore because it can have a major impact on your circuit board’s electrical performance and component reliability levels. That is why, we strictly control all the conditions of production, excluding such risks as solder beading. All our PCBs from the most basic to the most complicated PCBs go through the most modern technological processes and stringent quality assurance to meet the highest standards.
